dmesg - MAX HDD

Return To MAX HDD System Information

ACPI: Power Button [PWRB]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button [PWRF]
ACPI: Requesting acpi_cpufreq
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
tsc: Marking TSC unstable due to TSC halts in idle
ACPI: acpi_idle registered with cpuidle
GHES: HEST is not enabled!
Linux agpgart interface v0.103
brd: module loaded
loop: module loaded
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x8108 ctl 0x811c bmdma 0x80e0 irq 21
ata2: PATA max UDMA/100 cmd 0x8100 ctl 0x8118 bmdma 0x80e8 irq 21
ata_piix 0000:00:1f.2: MAP [
 P0 -- -- -- ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0x80f8 ctl 0x8114 bmdma 0x8020 irq 18
ata4: SATA max UDMA/133 cmd 0x80f0 ctl 0x8110 bmdma 0x8028 irq 18
libphy: Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky 
PPP generic driver version 2.4.2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:1a.7: setting latency timer to 64
ehci-pci 0000:00:1a.7: EHCI Host Controller
ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:1a.7: debug port 1
ehci-pci 0000:00:1a.7: cache line size of 64 is not supported
ehci-pci 0000:00:1a.7: irq 21, io mem 0xdb504c00
ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.8.0-21-generic ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ehci-pci 0000:00:1d.7: setting latency timer to 64
ehci-pci 0000:00:1d.7: EHCI Host Controller
ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci-pci 0000:00:1d.7: debug port 1
ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
ehci-pci 0000:00:1d.7: irq 20, io mem 0xdb504800
ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 3.8.0-21-generic ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 20, io base 0x000080c0
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 3.8.0-21-generic uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 16, io base 0x000080a0
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 3.8.0-21-generic uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 16, io base 0x00008080
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 3.8.0-21-generic uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.0
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 18, io base 0x00008060
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 3.8.0-21-generic uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.1
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 21, io base 0x00008040
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 3.8.0-21-generic uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.2
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
i8042: PNP: No PS/2 controller found. Probing ports directly.
ata1.01: ATAPI: MATSHITA DVD+/-RW UJ-867S, 1.00, max UDMA/33
ata1.01: configured for UDMA/33
ata3.00: ATA-8: FUJITSU MHY2200BH, 0081000D, max UDMA/100
ata3.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/100
ACPI: Battery Slot [BAT0] (battery present)
i8042: No controller found
mousedev: PS/2 mouse device common for all mice
scsi 0:0:1:0: CD-ROM            MATSHITA DVD+-RW UJ-867S  1.00 PQ: 0 ANSI: 5
rtc_cmos 00:07: RTC can wake from S4
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: [email protected]
cpuidle: using governor ladder
cpuidle: using governor menu
ledtrig-cpu: registered to indicate activity on CPUs
EFI Variables Facility v0.08 2004-May-17
ashmem: initialized
TCP: cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Key type dns_resolver registered
Loading module verification certificates
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda caddy
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 0:0:1:0: Attached scsi CD-ROM sr0
sr 0:0:1:0: Attached scsi generic sg0 type 5
scsi 2:0:0:0: Direct-Access     ATA      FUJITSU MHY2200B 0081 PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: Attached scsi generic sg1 type 0
MODSIGN: Loaded cert 'Magrathea: Glacier signing key: da639d7d39047796a6cdf66158dce65752f170ea'
registered taskstats version 1
Key type trusted registered
Key type encrypted registered
rtc_cmos 00:07: setting system clock to 2013-06-11 09:34:47 UTC (1370943287)
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
 sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9
sd 2:0:0:0: [sda] Attached SCSI disk
Freeing unused kernel memory: 992k freed
Write protecting the kernel read-only data: 12288k
Freeing unused kernel memory: 1176k freed
Freeing unused kernel memory: 1080k freed
udevd[104]: starting version 175
Disabling lock debugging due to kernel taint
sky2: driver version 1.30
sky2 0000:0c:00.0: Yukon-2 EC Ultra chip revision 3
ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20121018/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
lpc_ich: Resource conflict(s) found affecting gpio_ich
sky2 0000:0c:00.0: irq 45 for MSI/MSI-X
ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input4
sky2 0000:0c:00.0 eth0: addr 00:1e:c2:1c:1e:f9
nvidia: module license 'NVIDIA' taints kernel.
cfg80211: Calling CRDA to update world regulatory domain
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
applesmc: key=261 fan=2 temp=14 index=14 acc=1 lux=2 kbd=1
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  313.30  Wed Mar 27 16:56:45 PDT 2013
microcode: CPU0 sig=0x10676, pf=0x80, revision=0x60c
INFO @wl_cfg80211_attach : Registered CFG80211 phy
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
lib80211_crypt: registered algorithm 'TKIP'
firewire_ohci 0000:0d:03.0: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x2
eth1: Broadcom BCM4328 802.11 Hybrid Wireless Controller 6.20.155.1 (r326264)
hda_codec: ALC889A: SKU not ready 0x400000f0
input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
microcode: CPU1 sig=0x10676, pf=0x80, revision=0x60c
microcode: Microcode Update Driver: v2.00 , Peter Oruba
input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
input: applesmc as /devices/platform/applesmc.768/input/input7
usbcore: registered new interface driver bcm5974
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
[drm] Initialized drm 1.1.0 20060810
wmi: Mapper loaded
usb 2-4: new high-speed USB device number 2 using ehci-pci
device-mapper: multipath: version 1.5.1 loaded
nbd: registered device at major 43
usb 2-4: New USB device found, idVendor=05ac, idProduct=8502
usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-4: Product: Built-in iSight
usb 2-4: Manufacturer: Apple Inc.
usb 2-4: SerialNumber: 8T81V06740003L00
firewire_core 0000:0d:03.0: created device fw0: GUID 001f5bfffe271822, S800
usb 3-1: new full-speed USB device number 2 using uhci_hcd
usb 3-1: New USB device found, idVendor=0a5c, idProduct=4500
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: BRCM2046 Hub
usb 3-1: Manufacturer: Apple Inc.
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 3 ports detected
usb 7-1: new low-speed USB device number 2 using uhci_hcd
usb 7-1: New USB device found, idVendor=05ac, idProduct=8242
usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 7-1: Product: IR Receiver
usb 7-1: Manufacturer: Apple Computer, Inc.
apple 0003:05AC:8242.0001: hiddev0,hidraw0: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
usb 7-2: new full-speed USB device number 3 using uhci_hcd
video LNXVIDEO:00: Restoring backlight state
EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
usb 7-2: New USB device found, idVendor=05ac, idProduct=0230
usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 7-2: Product: Apple Internal Keyboard / Trackpad
usb 7-2: Manufacturer: Apple, Inc.
input: Apple, Inc. Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.0/input/input8
apple 0003:05AC:0230.0002: input,hidraw1: USB HID v1.11 Keyboard [Apple, Inc. Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input0
apple 0003:05AC:0230.0003: hidraw2: USB HID v1.11 Device [Apple, Inc. Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input1
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input9
usb 3-1.1: new full-speed USB device number 3 using uhci_hcd
usb 3-1.1: New USB device found, idVendor=05ac, idProduct=820f
usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-1.1: Product: Bluetooth USB Host Controller
usb 3-1.1: Manufacturer: Apple Inc.
usb 3-1.1: SerialNumber: 001EC28C8DEF
usb 3-1.2: new full-speed USB device number 4 using uhci_hcd
usb 3-1.2: New USB device found, idVendor=05ac, idProduct=820a
usb 3-1.2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
input: HID 05ac:820a as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.2/3-1.2:1.0/input/input10
hid-generic 0003:05AC:820A.0004: input,hidraw3: USB HID v1.11 Keyboard [HID 05ac:820a] on usb-0000:00:1a.0-1.2/input0
usb 3-1.3: new full-speed USB device number 5 using uhci_hcd
usb 3-1.3: New USB device found, idVendor=05ac, idProduct=820b
usb 3-1.3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
input: HID 05ac:820b as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.3/3-1.3:1.0/input/input11
hid-generic 0003:05AC:820B.0005: input,hidraw4: USB HID v1.11 Mouse [HID 05ac:820b] on usb-0000:00:1a.0-1.3/input0
Adding 8396796k swap on /dev/sda2.  Priority:-1 extents:1 across:8396796k 
Adding 2065000k swap on /dev/sda5.  Priority:-2 extents:1 across:2065000k 
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
udevd[514]: starting version 175
lp: driver loaded but no devices found
type=1400 audit(1370943299.637:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=616 comm="apparmor_parser"
type=1400 audit(1370943299.637:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=617 comm="apparmor_parser"
type=1400 audit(1370943299.641:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=616 comm="apparmor_parser"
type=1400 audit(1370943299.641:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=617 comm="apparmor_parser"
type=1400 audit(1370943299.641:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=616 comm="apparmor_parser"
type=1400 audit(1370943299.641:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=617 comm="apparmor_parser"
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
usbcore: registered new interface driver btusb
usb 3-1.2: USB disconnect, device number 4
usb 3-1.3: USB disconnect, device number 5
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device Built-in iSight (05ac:8502)
input: Built-in iSight as /devices/pci0000:00/0000:00:1d.7/usb2/2-4/2-4:1.0/input/input12
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
init: udev-fallback-graphics main process (1121) terminated with status 1
EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro
EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null)
init: failsafe main process (1208) killed by TERM signal
type=1400 audit(1370943303.881:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1295 comm="apparmor_parser"
type=1400 audit(1370943303.881:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper//chromium_browser" pid=1295 comm="apparmor_parser"
type=1400 audit(1370943303.881:10): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1296 comm="apparmor_parser"
type=1400 audit(1370943303.881:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1296 comm="apparmor_parser"
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
init: gdm main process (1370) killed by TERM signal
init: avahi-cups-reload main process (1466) terminated with status 1
ppdev: user-space parallel port driver
audit_printk_skb: 42 callbacks suppressed
type=1400 audit(1370943304.797:26): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1490 comm="apparmor_parser"
type=1400 audit(1370943304.797:27): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1490 comm="apparmor_parser"
Non-volatile memory driver v1.3
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
applesmc: light sensor data length set to 6
EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro
EXT4-fs (sda8): re-mounted. Opts: (null)
init: plymouth-upstart-bridge main process (1260) killed by TERM signal
applesmc: send_byte(0x30, 0x0300) fail: 0x00
applesmc: TW0P: read arg fail
applesmc: send_byte(0x4d, 0x0300) fail: 0x00
applesmc: F0Mn: write arg fail
ehci-pci 0000:00:1d.7: setting latency timer to 64
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
applesmc: send_byte(0x30, 0x0300) fail: 0x00
applesmc: TG0H: read arg fail
applesmc: send_byte(0x50, 0x0300) fail: 0x00
applesmc: Tm0P: read arg fail
applesmc: send_byte(0x31, 0x0300) fail: 0x00
applesmc: ALV1: read arg fail
applesmc: send_byte(0x54, 0x0300) fail: 0x00
applesmc: TG0H: read arg fail
applesmc: send_byte(0x44, 0x0300) fail: 0x00
applesmc: TG0D: read arg fail
applesmc: send_byte(0x30, 0x0300) fail: 0x00
applesmc: TG0H: read arg fail
applesmc: send_byte(0x54, 0x0300) fail: 0x00
applesmc: TG0H: read arg fail
applesmc: send_byte(0x56, 0x0300) fail: 0x00
applesmc: ALV1: read arg fail
applesmc: send_byte(0x30, 0x0300) fail: 0x00
applesmc: TW0P: read arg fail
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
CE: hpet increased min_delta_ns to 20113 nsec
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
sky2 0000:0c:00.0 eth0: disabling interface
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.1: setting latency timer to 64
ehci-pci 0000:00:1a.7: setting latency timer to 64
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.1: setting latency timer to 64
ehci-pci 0000:00:1d.7: setting latency timer to 64
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
ata_piix 0000:00:1f.1: power state changed by ACPI to D3hot
pciehp 0000:00:1c.5:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:01.0:pcie04: pciehp_suspend ENTRY
PM: suspend of devices complete after 943.566 msecs
PM: late suspend of devices complete after 0.362 msecs
ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 187.650 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
smpboot: CPU 1 is now offline
Extended CMOS year: 2000
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Extended CMOS year: 2000
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
ACPI: Waking up from system sleep state S3
uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
PM: noirq resume of devices complete after 252.213 msecs
PM: early resume of devices complete after 0.121 msecs
pciehp 0000:00:01.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:01.0:pcie04: Card present on Slot(1)
uhci_hcd 0000:00:1a.0: setting latency timer to 64
usb usb3: root hub lost power or was reset
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb4: root hub lost power or was reset
ehci-pci 0000:00:1a.7: setting latency timer to 64
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_resume ENTRY
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
pciehp 0000:00:1c.4:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.5:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb5: root hub lost power or was reset
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb6: root hub lost power or was reset
usb usb7: root hub lost power or was reset
ehci-pci 0000:00:1d.7: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
ata_piix 0000:00:1f.1: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: ACPI cmd ef/03:ff:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: configured for UDMA/33
usb 3-1: reset full-speed USB device number 2 using uhci_hcd
firewire_core 0000:0d:03.0: rediscovered device fw0
usb 7-1: reset low-speed USB device number 2 using uhci_hcd
pciehp 0000:00:01.0:pcie04: Device 0000:01:00.0 already exists at 0000:01:00, cannot hot-add
pciehp 0000:00:01.0:pcie04: Cannot add device at 0000:01:00
usb 7-2: reset full-speed USB device number 3 using uhci_hcd
bcm5974 7-2:1.2: no reset_resume for driver bcm5974?
usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
btusb 3-1.1:1.0: no reset_resume for driver btusb?
btusb 3-1.1:1.1: no reset_resume for driver btusb?
ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] Starting disk
PM: resume of devices complete after 1783.912 msecs
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input13
Restarting tasks ... done.
video LNXVIDEO:00: Restoring backlight state
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
sky2 0000:0c:00.0 eth0: disabling interface
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
ata_piix 0000:00:1f.1: power state changed by ACPI to D3hot
pciehp 0000:00:1c.5:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
pciehp 0000:00:1c.2:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: Card present on Slot(4)
pciehp 0000:00:01.0:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
PM: suspend of devices complete after 951.505 msecs
PM: late suspend of devices complete after 0.365 msecs
ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 187.661 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
smpboot: CPU 1 is now offline
Extended CMOS year: 2000
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Extended CMOS year: 2000
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
ACPI: Waking up from system sleep state S3
uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
PM: noirq resume of devices complete after 252.200 msecs
pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
pciehp 0000:00:1c.4:pcie04: Card present on Slot(4)
pciehp 0000:00:01.0:pcie04: Card present on Slot(1)
PM: early resume of devices complete after 0.124 msecs
pciehp 0000:00:01.0:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1a.0: setting latency timer to 64
usb usb3: root hub lost power or was reset
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb4: root hub lost power or was reset
ehci-pci 0000:00:1a.7: setting latency timer to 64
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
pciehp 0000:00:1c.2:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.5:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.1: setting latency timer to 64
usb usb5: root hub lost power or was reset
usb usb6: root hub lost power or was reset
uhci_hcd 0000:00:1d.2: setting latency timer to 64
ehci-pci 0000:00:1d.7: setting latency timer to 64
usb usb7: root hub lost power or was reset
pci 0000:00:1e.0: setting latency timer to 64
ata_piix 0000:00:1f.1: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: ACPI cmd ef/03:ff:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: configured for UDMA/33
usb 3-1: reset full-speed USB device number 2 using uhci_hcd
firewire_core 0000:0d:03.0: rediscovered device fw0
usb 7-2: reset full-speed USB device number 3 using uhci_hcd
bcm5974 7-2:1.2: no reset_resume for driver bcm5974?
usb 7-1: reset low-speed USB device number 2 using uhci_hcd
pciehp 0000:00:01.0:pcie04: Device 0000:01:00.0 already exists at 0000:01:00, cannot hot-add
pciehp 0000:00:01.0:pcie04: Cannot add device at 0000:01:00
usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
btusb 3-1.1:1.0: no reset_resume for driver btusb?
btusb 3-1.1:1.1: no reset_resume for driver btusb?
ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/100
Extended CMOS year: 2000
sd 2:0:0:0: [sda] Starting disk
PM: resume of devices complete after 1793.265 msecs
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input14
Restarting tasks ... done.
video LNXVIDEO:00: Restoring backlight state
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
sky2 0000:0c:00.0 eth0: disabling interface
init: anacron main process (5238) killed by TERM signal
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
pciehp 0000:00:1c.5:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
ata_piix 0000:00:1f.1: power state changed by ACPI to D3hot
pciehp 0000:00:1c.4:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:01.0:pcie04: pciehp_suspend ENTRY
PM: suspend of devices complete after 947.448 msecs
PM: late suspend of devices complete after 0.366 msecs
ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 187.682 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
smpboot: CPU 1 is now offline
Extended CMOS year: 2000
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Extended CMOS year: 2000
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
ACPI: Waking up from system sleep state S3
uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
PM: noirq resume of devices complete after 252.163 msecs
pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
pciehp 0000:00:1c.4:pcie04: Card present on Slot(4)
pciehp 0000:00:01.0:pcie04: Card present on Slot(1)
PM: early resume of devices complete after 0.122 msecs
pciehp 0000:00:01.0:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb3: root hub lost power or was reset
usb usb4: root hub lost power or was reset
ehci-pci 0000:00:1a.7: setting latency timer to 64
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_resume ENTRY
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
pciehp 0000:00:1c.4:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.5:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb5: root hub lost power or was reset
uhci_hcd 0000:00:1d.1: setting latency timer to 64
usb usb6: root hub lost power or was reset
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb7: root hub lost power or was reset
ehci-pci 0000:00:1d.7: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
ata_piix 0000:00:1f.1: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: ACPI cmd ef/03:ff:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: configured for UDMA/33
usb 3-1: reset full-speed USB device number 2 using uhci_hcd
firewire_core 0000:0d:03.0: rediscovered device fw0
usb 7-1: reset low-speed USB device number 2 using uhci_hcd
pciehp 0000:00:01.0:pcie04: Device 0000:01:00.0 already exists at 0000:01:00, cannot hot-add
pciehp 0000:00:01.0:pcie04: Cannot add device at 0000:01:00
usb 7-2: reset full-speed USB device number 3 using uhci_hcd
bcm5974 7-2:1.2: no reset_resume for driver bcm5974?
usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
btusb 3-1.1:1.0: no reset_resume for driver btusb?
btusb 3-1.1:1.1: no reset_resume for driver btusb?
ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] Starting disk
PM: resume of devices complete after 1791.724 msecs
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input15
Restarting tasks ... done.
video LNXVIDEO:00: Restoring backlight state
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
sky2 0000:0c:00.0 eth0: disabling interface
init: anacron main process (5974) killed by TERM signal
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
ata_piix 0000:00:1f.1: power state changed by ACPI to D3hot
pciehp 0000:00:1c.5:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:01.0:pcie04: pciehp_suspend ENTRY
PM: suspend of devices complete after 955.467 msecs
PM: late suspend of devices complete after 0.362 msecs
ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 187.680 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
smpboot: CPU 1 is now offline
Extended CMOS year: 2000
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Extended CMOS year: 2000
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
ACPI: Waking up from system sleep state S3
uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
PM: noirq resume of devices complete after 252.206 msecs
pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
pciehp 0000:00:1c.4:pcie04: Card present on Slot(4)
pciehp 0000:00:01.0:pcie04: Card present on Slot(1)
PM: early resume of devices complete after 0.122 msecs
pciehp 0000:00:01.0:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1a.0: setting latency timer to 64
usb usb3: root hub lost power or was reset
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb4: root hub lost power or was reset
ehci-pci 0000:00:1a.7: setting latency timer to 64
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.5:pcie04: pciehp_resume ENTRY
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb5: root hub lost power or was reset
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb6: root hub lost power or was reset
ehci-pci 0000:00:1d.7: setting latency timer to 64
usb usb7: root hub lost power or was reset
pci 0000:00:1e.0: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
ata_piix 0000:00:1f.1: setting latency timer to 64
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: ACPI cmd ef/03:ff:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: configured for UDMA/33
usb 7-1: reset low-speed USB device number 2 using uhci_hcd
firewire_core 0000:0d:03.0: rediscovered device fw0
usb 3-1: reset full-speed USB device number 2 using uhci_hcd
pciehp 0000:00:01.0:pcie04: Device 0000:01:00.0 already exists at 0000:01:00, cannot hot-add
pciehp 0000:00:01.0:pcie04: Cannot add device at 0000:01:00
usb 7-2: reset full-speed USB device number 3 using uhci_hcd
bcm5974 7-2:1.2: no reset_resume for driver bcm5974?
usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
btusb 3-1.1:1.0: no reset_resume for driver btusb?
btusb 3-1.1:1.1: no reset_resume for driver btusb?
ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] Starting disk
PM: resume of devices complete after 1790.029 msecs
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input16
Restarting tasks ... done.
video LNXVIDEO:00: Restoring backlight state
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
sky2 0000:0c:00.0 eth0: disabling interface
init: anacron main process (6703) killed by TERM signal
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
ata_piix 0000:00:1f.1: power state changed by ACPI to D3hot
pciehp 0000:00:1c.5:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:01.0:pcie04: pciehp_suspend ENTRY
PM: suspend of devices complete after 943.457 msecs
PM: late suspend of devices complete after 0.365 msecs
ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 187.660 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
smpboot: CPU 1 is now offline
Extended CMOS year: 2000
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Extended CMOS year: 2000
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
ACPI: Waking up from system sleep state S3
uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
PM: noirq resume of devices complete after 252.204 msecs
pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
pciehp 0000:00:1c.4:pcie04: Card present on Slot(4)
pciehp 0000:00:01.0:pcie04: Card present on Slot(1)
PM: early resume of devices complete after 0.123 msecs
pciehp 0000:00:01.0:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb3: root hub lost power or was reset
usb usb4: root hub lost power or was reset
ehci-pci 0000:00:1a.7: setting latency timer to 64
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_resume ENTRY
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
pciehp 0000:00:1c.5:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb5: root hub lost power or was reset
uhci_hcd 0000:00:1d.1: setting latency timer to 64
usb usb6: root hub lost power or was reset
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb7: root hub lost power or was reset
ehci-pci 0000:00:1d.7: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
ata_piix 0000:00:1f.1: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: ACPI cmd ef/03:ff:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: configured for UDMA/33
usb 3-1: reset full-speed USB device number 2 using uhci_hcd
firewire_core 0000:0d:03.0: rediscovered device fw0
usb 7-1: reset low-speed USB device number 2 using uhci_hcd
pciehp 0000:00:01.0:pcie04: Device 0000:01:00.0 already exists at 0000:01:00, cannot hot-add
pciehp 0000:00:01.0:pcie04: Cannot add device at 0000:01:00
usb 7-2: reset full-speed USB device number 3 using uhci_hcd
bcm5974 7-2:1.2: no reset_resume for driver bcm5974?
usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
btusb 3-1.1:1.0: no reset_resume for driver btusb?
btusb 3-1.1:1.1: no reset_resume for driver btusb?
ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] Starting disk
PM: resume of devices complete after 1787.821 msecs
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input17
Restarting tasks ... done.
video LNXVIDEO:00: Restoring backlight state
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
applesmc: send_byte(0x54, 0x0300) fail: 0x00
applesmc: TG0D: read arg fail
applesmc: send_byte(0x47, 0x0300) fail: 0x00
applesmc: TG0H: read arg fail
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
sky2 0000:0c:00.0 eth0: disabling interface
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
ata_piix 0000:00:1f.1: power state changed by ACPI to D3hot
pciehp 0000:00:1c.5:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:01.0:pcie04: pciehp_suspend ENTRY
PM: suspend of devices complete after 979.528 msecs
PM: late suspend of devices complete after 0.352 msecs
ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 187.674 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
smpboot: CPU 1 is now offline
Extended CMOS year: 2000
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Extended CMOS year: 2000
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
ACPI: Waking up from system sleep state S3
uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
PM: noirq resume of devices complete after 252.200 msecs
pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
pciehp 0000:00:1c.4:pcie04: Card present on Slot(4)
pciehp 0000:00:01.0:pcie04: Card present on Slot(1)
PM: early resume of devices complete after 0.126 msecs
pciehp 0000:00:01.0:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1a.0: setting latency timer to 64
usb usb3: root hub lost power or was reset
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb4: root hub lost power or was reset
ehci-pci 0000:00:1a.7: setting latency timer to 64
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_resume ENTRY
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
pciehp 0000:00:1c.5:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb5: root hub lost power or was reset
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb6: root hub lost power or was reset
usb usb7: root hub lost power or was reset
ehci-pci 0000:00:1d.7: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
ata_piix 0000:00:1f.1: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: ACPI cmd ef/03:ff:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: configured for UDMA/33
usb 3-1: reset full-speed USB device number 2 using uhci_hcd
firewire_core 0000:0d:03.0: rediscovered device fw0
usb 7-1: reset low-speed USB device number 2 using uhci_hcd
pciehp 0000:00:01.0:pcie04: Device 0000:01:00.0 already exists at 0000:01:00, cannot hot-add
pciehp 0000:00:01.0:pcie04: Cannot add device at 0000:01:00
usb 7-2: reset full-speed USB device number 3 using uhci_hcd
bcm5974 7-2:1.2: no reset_resume for driver bcm5974?
usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
btusb 3-1.1:1.0: no reset_resume for driver btusb?
btusb 3-1.1:1.1: no reset_resume for driver btusb?
ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] Starting disk
PM: resume of devices complete after 1811.843 msecs
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input18
Restarting tasks ... done.
video LNXVIDEO:00: Restoring backlight state
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
sky2 0000:0c:00.0 eth0: disabling interface
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
ata_piix 0000:00:1f.1: power state changed by ACPI to D3hot
pciehp 0000:00:1c.5:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:01.0:pcie04: pciehp_suspend ENTRY
PM: suspend of devices complete after 951.511 msecs
PM: late suspend of devices complete after 0.365 msecs
ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 187.663 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
smpboot: CPU 1 is now offline
Extended CMOS year: 2000
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Extended CMOS year: 2000
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
ACPI: Waking up from system sleep state S3
uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
PM: noirq resume of devices complete after 252.211 msecs
pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
pciehp 0000:00:1c.4:pcie04: Card present on Slot(4)
pciehp 0000:00:01.0:pcie04: Card present on Slot(1)
PM: early resume of devices complete after 0.125 msecs
pciehp 0000:00:01.0:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1a.0: setting latency timer to 64
usb usb3: root hub lost power or was reset
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb4: root hub lost power or was reset
ehci-pci 0000:00:1a.7: setting latency timer to 64
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.5:pcie04: pciehp_resume ENTRY
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb5: root hub lost power or was reset
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb6: root hub lost power or was reset
ehci-pci 0000:00:1d.7: setting latency timer to 64
usb usb7: root hub lost power or was reset
pci 0000:00:1e.0: setting latency timer to 64
ata_piix 0000:00:1f.1: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: ACPI cmd ef/03:ff:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: configured for UDMA/33
usb 7-2: reset full-speed USB device number 3 using uhci_hcd
bcm5974 7-2:1.2: no reset_resume for driver bcm5974?
firewire_core 0000:0d:03.0: rediscovered device fw0
usb 3-1: reset full-speed USB device number 2 using uhci_hcd
usb 7-1: reset low-speed USB device number 2 using uhci_hcd
pciehp 0000:00:01.0:pcie04: Device 0000:01:00.0 already exists at 0000:01:00, cannot hot-add
pciehp 0000:00:01.0:pcie04: Cannot add device at 0000:01:00
usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
btusb 3-1.1:1.0: no reset_resume for driver btusb?
btusb 3-1.1:1.1: no reset_resume for driver btusb?
ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] Starting disk
PM: resume of devices complete after 1783.518 msecs
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input19
Restarting tasks ... done.
video LNXVIDEO:00: Restoring backlight state
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
applesmc: send_byte(0x54, 0x0300) fail: 0x00
applesmc: Tm0P: read arg fail
applesmc: send_byte(0x24, 0x0300) fail: 0x00
applesmc: F0Mn: write data fail
applesmc: send_byte(0x50, 0x0300) fail: 0x00
applesmc: Tm0P: read arg fail
applesmc: send_byte(0x6e, 0x0300) fail: 0x00
applesmc: F0Mn: write arg fail
applesmc: send_byte(0x02, 0x0300) fail: 0x00
applesmc: F0Mn: write len fail
applesmc: send_byte(0x30, 0x0300) fail: 0x00
applesmc: TG0H: read arg fail
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
sky2 0000:0c:00.0 eth0: disabling interface
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
ata_piix 0000:00:1f.1: power state changed by ACPI to D3hot
pciehp 0000:00:1c.5:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:01.0:pcie04: pciehp_suspend ENTRY
PM: suspend of devices complete after 987.505 msecs
PM: late suspend of devices complete after 0.367 msecs
ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 187.671 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
smpboot: CPU 1 is now offline
Extended CMOS year: 2000
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Extended CMOS year: 2000
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
ACPI: Waking up from system sleep state S3
uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
PM: noirq resume of devices complete after 252.201 msecs
pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
pciehp 0000:00:1c.4:pcie04: Card present on Slot(4)
pciehp 0000:00:01.0:pcie04: Card present on Slot(1)
PM: early resume of devices complete after 0.122 msecs
pciehp 0000:00:01.0:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1a.0: setting latency timer to 64
usb usb3: root hub lost power or was reset
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb4: root hub lost power or was reset
ehci-pci 0000:00:1a.7: setting latency timer to 64
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_resume ENTRY
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
pciehp 0000:00:1c.4:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.5:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.1: setting latency timer to 64
usb usb5: root hub lost power or was reset
usb usb6: root hub lost power or was reset
uhci_hcd 0000:00:1d.2: setting latency timer to 64
ehci-pci 0000:00:1d.7: setting latency timer to 64
usb usb7: root hub lost power or was reset
pci 0000:00:1e.0: setting latency timer to 64
ata_piix 0000:00:1f.1: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: ACPI cmd ef/03:ff:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: configured for UDMA/33
usb 3-1: reset full-speed USB device number 2 using uhci_hcd
firewire_core 0000:0d:03.0: rediscovered device fw0
usb 7-1: reset low-speed USB device number 2 using uhci_hcd
pciehp 0000:00:01.0:pcie04: Device 0000:01:00.0 already exists at 0000:01:00, cannot hot-add
pciehp 0000:00:01.0:pcie04: Cannot add device at 0000:01:00
usb 7-2: reset full-speed USB device number 3 using uhci_hcd
bcm5974 7-2:1.2: no reset_resume for driver bcm5974?
usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
btusb 3-1.1:1.0: no reset_resume for driver btusb?
btusb 3-1.1:1.1: no reset_resume for driver btusb?
ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] Starting disk
PM: resume of devices complete after 1791.863 msecs
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input20
Restarting tasks ... done.
video LNXVIDEO:00: Restoring backlight state
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
applesmc: send_byte(0x57, 0x0300) fail: 0x00
applesmc: TW0P: read arg fail
applesmc: send_byte(0x57, 0x0300) fail: 0x00
applesmc: TW0P: read arg fail
applesmc: send_byte(0x44, 0x0300) fail: 0x00
applesmc: TG0D: read arg fail
applesmc: send_byte(0x02, 0x0300) fail: 0x00
applesmc: TG0H: read len fail
applesmc: send_byte(0x57, 0x0300) fail: 0x00
applesmc: TW0P: read arg fail
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
sky2 0000:0c:00.0 eth0: disabling interface
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
ata_piix 0000:00:1f.1: power state changed by ACPI to D3hot
pciehp 0000:00:1c.5:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:01.0:pcie04: pciehp_suspend ENTRY
PM: suspend of devices complete after 947.487 msecs
PM: late suspend of devices complete after 0.368 msecs
ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 187.678 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
smpboot: CPU 1 is now offline
Extended CMOS year: 2000
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Extended CMOS year: 2000
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
ACPI: Waking up from system sleep state S3
uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: power state changed by ACPI to D0
ata_piix 0000:00:1f.1: power state changed by ACPI to D0
PM: noirq resume of devices complete after 252.209 msecs
pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
pciehp 0000:00:1c.4:pcie04: Card present on Slot(4)
pciehp 0000:00:01.0:pcie04: Card present on Slot(1)
PM: early resume of devices complete after 0.123 msecs
pciehp 0000:00:01.0:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb3: root hub lost power or was reset
ehci-pci 0000:00:1a.7: setting latency timer to 64
usb usb4: root hub lost power or was reset
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.2:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.4:pcie04: pciehp_resume ENTRY
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
pciehp 0000:00:1c.5:pcie04: pciehp_resume ENTRY
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.1: setting latency timer to 64
usb usb5: root hub lost power or was reset
usb usb6: root hub lost power or was reset
uhci_hcd 0000:00:1d.2: setting latency timer to 64
ehci-pci 0000:00:1d.7: setting latency timer to 64
usb usb7: root hub lost power or was reset
pci 0000:00:1e.0: setting latency timer to 64
ata_piix 0000:00:1f.1: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.4:pcie04: Device 0000:0b:00.0 already exists at 0000:0b:00, cannot hot-add
pciehp 0000:00:1c.4:pcie04: Cannot add device at 0000:0b:00
pciehp 0000:00:1c.5:pcie04: Device 0000:0c:00.0 already exists at 0000:0c:00, cannot hot-add
pciehp 0000:00:1c.5:pcie04: Cannot add device at 0000:0c:00
ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: ACPI cmd ef/03:ff:00:00:00:b0 (SET FEATURES) filtered out
ata1.01: configured for UDMA/33
usb 3-1: reset full-speed USB device number 2 using uhci_hcd
firewire_core 0000:0d:03.0: rediscovered device fw0
usb 7-1: reset low-speed USB device number 2 using uhci_hcd
pciehp 0000:00:01.0:pcie04: Device 0000:01:00.0 already exists at 0000:01:00, cannot hot-add
pciehp 0000:00:01.0:pcie04: Cannot add device at 0000:01:00
usb 7-2: reset full-speed USB device number 3 using uhci_hcd
bcm5974 7-2:1.2: no reset_resume for driver bcm5974?
usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
btusb 3-1.1:1.0: no reset_resume for driver btusb?
btusb 3-1.1:1.1: no reset_resume for driver btusb?
ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] Starting disk
PM: resume of devices complete after 1787.837 msecs
input: bcm5974 as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input21
Restarting tasks ... done.
video LNXVIDEO:00: Restoring backlight state
applesmc: send_byte(0x02, 0x0300) fail: 0x00
applesmc: F0Mn: write len fail
sky2 0000:0c:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
applesmc: send_byte(0x44, 0x0300) fail: 0x00
applesmc: TG0D: read arg fail
applesmc: send_byte(0x2b, 0x0300) fail: 0x00
applesmc: F1Mn: write data fail
applesmc: send_byte(0x54, 0x0300) fail: 0x00
applesmc: Tm0P: read arg fail
applesmc: send_byte(0x30, 0x0300) fail: 0x00
applesmc: TG0H: read arg fail
applesmc: send_byte(0x30, 0x0300) fail: 0x00
applesmc: F0Mn: write arg fail
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
JFS: nTxBlock = 8192, nTxLock = 65536
NTFS driver 2.1.30 [Flags: R/O MODULE].
QNX4 filesystem 0.2.3 registered.
Btrfs loaded
applesmc: send_byte(0x54, 0x0300) fail: 0x00
applesmc: Tm0P: read arg fail
applesmc: send_byte(0x30, 0x0300) fail: 0x00
applesmc: TG0D: read arg fail
applesmc: send_byte(0x6e, 0x0300) fail: 0x00
applesmc: F0Mn: write arg fail
applesmc: send_byte(0x6e, 0x0300) fail: 0x00
applesmc: F0Mn: write arg fail
applesmc: send_byte(0x27, 0x0300) fail: 0x00
applesmc: F0Mn: write data fail
applesmc: send_byte(0x02, 0x0300) fail: 0x00
applesmc: F0Mn: write len fail
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
applesmc: send_byte(0x6e, 0x0300) fail: 0x00
applesmc: F0Mn: write arg fail
applesmc: send_byte(0x54, 0x0300) fail: 0x00
applesmc: Tm0P: read arg fail

Return To MAX HDD System Information